Clam Daemon(8)

NAME

clamd - an anti-virus daemon

SYNOPSIS

clamd [options]

DESCRIPTION

The daemon listens for incoming connections on Unix and/or TCP socket and scans files or directories on demand. It reads the configuration from /usr/pkg/etc/clamd.conf

COMMANDS

It's recommended to prefix clamd commands with the letter z (eg. zSCAN) to indicate that the command will be delimited by a NULL character and that clamd should continue reading command data until a NULL character is read. The null delimiter assures that the complete command and its entire argument will be processed as a single command. Alternatively commands may be prefixed with the letter n (e.g. nSCAN) to use a newline character as the delimiter. Clamd replies will honour the requested terminator in turn. If clamd doesn't recognize the command, or the command doesn't follow the requirements specified below, it will reply with an error message, and close the connection.

Clamd recognizes the following commands:

PING
    Check the server's state. It should reply with "PONG".

VERSION
    Print program and database versions.

RELOAD
    Reload the virus databases.

SHUTDOWN
    Perform a clean exit.

SCAN file/directory
    Scan a file or a directory (recursively) with archive support enabled (if not disabled in clamd.conf). A full path is required.

CONTSCAN file/directory
    Scan file or directory (recursively) with archive support enabled and don't stop the scanning when a virus is found.

MULTISCAN file/directory
    Scan a directory recursively using multiple threads (to make the scanning faster on SMP machines). If the target is not a directory, clamd falls back to non-multiscan scanning behavior.

ALLMATCHSCAN file/directory
    It is mandatory to prefix this command with n or z. ALLMATCHSCAN works just like SCAN except that it sets a mode where scanning continues after finding a match within a file. This command may be disabled with AllowAllMatchScan in clamd.conf. If disabled, clamd replies with an ALLMATCHSCAN error.

INSTREAM
    It is mandatory to prefix this command with n or z. Scan a stream of data. The stream is sent to clamd in chunks, after INSTREAM, on the same socket on which the command was sent. This avoids the overhead of establishing new TCP connections and problems with NAT. The format of the chunk is: '<length><data>' where <length> is the size of the following data in bytes expressed as a 4 byte unsigned integer in network byte order and <data> is the actual chunk. Streaming is terminated by sending a zero-length chunk. Note: do not exceed StreamMaxLength as defined in clamd.conf, otherwise clamd will reply with INSTREAM size limit exceeded and close the connection.

FILDES
    It is mandatory to newline terminate this command, or prefix with n or z. This command only works on UNIX domain sockets. Scan a file descriptor. After issuing a FILDES command a subsequent rfc2292/bsd4.4 style packet (with at least one dummy character) is sent to clamd carrying the file descriptor to be scanned inside the ancillary data. Alternatively the file descriptor may be sent in the same packet, including the extra character.

STATS
    It is mandatory to newline terminate this command, or prefix with n or z, it is recommended to only use the z prefix. Replies with statistics about the scan queue, contents of scan queue, and memory usage. The exact reply format is subject to change in future releases.

IDSESSION, END
    It is mandatory to prefix this command with n or z, and all commands inside IDSESSION must be prefixed. Start/end a clamd session. Within a session multiple SCAN, INSTREAM, FILDES, VERSION, VERSIONCOMMANDS, PING, and STATS commands can be sent on the same socket without opening new connections. CONTSCAN, MULTISCAN, ALLMATCHSCAN, RELOAD, and SHUTDOWN are not accepted inside an IDSESSION. Replies from clamd will be in the form '<id>: <response>' where <id> is the request number (in ascii, starting from 1) and <response> is the usual clamd reply. The reply lines have same delimiter as the corresponding command had. Clamd will process the commands asynchronously, and reply as soon as it has finished processing. Clamd requires clients to read all the replies it sent, before sending more commands to prevent send() deadlocks. The recommended way to implement a client that uses IDSESSION is with non-blocking sockets, and a select()/poll() loop: whenever send would block, sleep in select/poll until either you can write more data, or read more replies. Note that using non-blocking sockets without the select/poll loop and alternating recv()/send() doesn't comply with clamd's requirements. If clamd detects that a client has deadlocked, it will close the connection. Note that clamd may close an IDSESSION connection too if you don't follow the protocol's requirements. The client can use the PING command to keep the connection alive.

VERSIONCOMMANDS
    It is mandatory to prefix this command with either n or z. It is recommended to use nVERSIONCOMMANDS. Print program and database versions, followed by "| COMMANDS:" and a space-delimited list of supported commands. Clamd <0.95 will recognize this as the VERSION command, and reply only with their version, without the commands list. This command can be used as an easy way to check for IDSESSION support for example.

REMOVED COMMANDS

STREAM
    The legacy STREAM command is no longer supported. Use INSTREAM instead.

NOT SUPPORTED COMMANDS

SESSION, END
    Start/end a clamd session which will allow you to run multiple commands per TCP session. (use IDSESSION instead)

OPTIONS

-h, --help
    Output help information and exit.

-V, --version
    Print the version number and exit.

-F, --foreground
    Run in foreground; do not daemonize.

--debug
    Enable debug mode.

-c FILE, --config-file=FILE
    Read configuration from FILE.

--fail-if-cvd-older-than=days
    Return with a nonzero error code if the virus database is older than the specified number of days.

--datadir=DIRECTORY
    Load signatures from DIRECTORY.

-p FILE, --pid=FILE
    Write the daemon's pid to FILE.

ENVIRONMENT VARIABLES

clamd uses the following environment variables:

LD_LIBRARY_PATH - May be used on startup to find the libclamunrar_iface shared library module to enable RAR archive support.

SIGNALS

Clamd recognizes the following signals:

SIGHUP
    Reopen the logfile.

SIGUSR2
    Reload the signature databases.

SIGTERM
    Perform a clean exit.

FILES

/usr/pkg/etc/clamd.conf

CREDITS
Please check the full documentation for credits.

AUTHOR

Tomasz Kojm <tkojm@clamav.net>

SEE ALSO

clamd.conf(5), clamdscan(1), freshclam(1), freshclam.conf(5), clamav-milter(8)